/*
@module  gpio
@summary GPIO操作
@catalog 外设API
@version 1.0
@date    2020.03.30
@demo gpio
@video https://www.bilibili.com/video/BV1hr4y1p7dt
@tag LUAT_USE_GPIO
*/
#include "luat_base.h"
#include "luat_gpio.h"
#include "luat_mem.h"
#include "luat_mcu.h"
#include "luat_msgbus.h"
#include "luat_timer.h"
#include "luat_rtos.h"
#include "luat_mcu.h"
#include <math.h>

#ifdef LUAT_USE_DRV_GPIO
#include "luat/drv_gpio.h"
#endif

#define LUAT_LOG_TAG "gpio"
#include "luat_log.h"

static int l_gpio_set(lua_State *L);
static int l_gpio_get(lua_State *L);
static int l_gpio_close(lua_State *L);
static int l_gpio_get_count(lua_State *L);
int l_gpio_handler(lua_State *L, void* ptr) ;

typedef struct gpio_ctx
{
    int lua_ref; // irq下的回调函数
    luat_rtos_timer_t timer;
    uint32_t irq_cnt;		//中断数量计数
    uint32_t latest_tick; // 防抖功能的最后tick数
    uint16_t conf_tick;   // 防抖设置的超时tick数
    uint8_t debounce_mode;
    uint8_t latest_state;
    uint8_t irq_type;
}gpio_ctx_t;

// 保存中断回调的数组
static gpio_ctx_t gpios[LUAT_GPIO_PIN_MAX];
static uint32_t default_gpio_pull = Luat_GPIO_DEFAULT;


// 记录GPIO电平,仅OUTPUT时可用
static uint8_t gpio_out_levels[(LUAT_GPIO_PIN_MAX + 7) / 8];

static uint8_t gpio_bit_get(int pin) {
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return 0;
    return (gpio_out_levels[pin/8] >> (pin%8)) & 0x01;
}

static void gpio_bit_set(int pin, uint8_t value) {
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return;
    uint8_t val = (gpio_out_levels[pin/8] >> (pin%8)) & 0x01;
    if (val == value)
        return; // 不变呀
    if (value == 0) {
        gpio_out_levels[pin/8] -= (1 << (pin%8));
    }
    else {
        gpio_out_levels[pin/8] += (1 << (pin%8));
    }
}

int l_gpio_debounce_timer_handler(lua_State *L, void* ptr) {
    (void)L;
    (void)ptr;

    rtos_msg_t* msg = (rtos_msg_t*)lua_topointer(L, -1);
    int pin = msg->arg1;
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return 0; // 超范围, 内存异常
    if (gpios[pin].lua_ref == 0)
        return 0; // 早关掉了
    if (gpios[pin].latest_state != luat_gpio_get(pin))
        return 0; // 电平变了
    if (gpios[pin].debounce_mode)
    {
        switch(gpios[pin].irq_type)
        {
        case Luat_GPIO_RISING:
        case Luat_GPIO_HIGH_IRQ:
        	if (!gpios[pin].latest_state) return 0;
        	break;
        case Luat_GPIO_FALLING:
        case Luat_GPIO_LOW_IRQ:
        	if (gpios[pin].latest_state) return 0;
        	break;
        }
    }

    lua_geti(L, LUA_REGISTRYINDEX, gpios[pin].lua_ref);
    if (!lua_isnil(L, -1)) {
        lua_pushinteger(L, gpios[pin].latest_state);
        lua_pushinteger(L, pin);
        lua_call(L, 2, 0);
    }
    return 0;
}

#ifndef LUAT_RTOS_API_NOTOK
static LUAT_RT_RET_TYPE l_gpio_debounce_mode1_cb(LUAT_RT_CB_PARAM) {
    int pin = (int)param;
    rtos_msg_t msg = {0};
    msg.handler = l_gpio_debounce_timer_handler;
    msg.arg1 = pin;
    luat_msgbus_put(&msg, 0);
}
#endif

static int luat_gpio_irq_count(int pin, void* args) {
	gpios[pin].irq_cnt++;
	return 0;
}

int luat_gpio_irq_default(int pin, void* args) {
    rtos_msg_t msg = {0};
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX) {
        return 0;
    }

    if (pin < LUAT_GPIO_PIN_MAX && gpios[pin].conf_tick > 0) {
        // 防抖模式0, 触发后冷却N个ms
        if (gpios[pin].debounce_mode == 0) {
            uint32_t ticks = (uint32_t)luat_mcu_ticks();
            uint32_t diff = (ticks > gpios[pin].latest_tick) ? (ticks - gpios[pin].latest_tick) : (gpios[pin].latest_tick - ticks);
            if (diff >= gpios[pin].conf_tick) {
                gpios[pin].latest_tick = ticks;
            }
            else {
                // 防抖生效, 直接返回
            return 0;
            }
        }
        #ifndef LUAT_RTOS_API_NOTOK
        // 防抖模式1, 触发后延时N个ms, 电平依然不变才触发
        else if (gpios[pin].debounce_mode == 1) {
            if (gpios[pin].timer == NULL || gpios[pin].conf_tick == 0) {
                return 0; // timer被释放了?
            }
            gpios[pin].latest_state = luat_gpio_get(pin);
            luat_rtos_timer_stop(gpios[pin].timer);
            luat_rtos_timer_start(gpios[pin].timer, gpios[pin].conf_tick, 0, l_gpio_debounce_mode1_cb, (void*)pin);
            return 0;
        }
        #endif
    }

    msg.handler = l_gpio_handler;
    msg.ptr = NULL;
    msg.arg1 = pin;
    msg.arg2 = (int)args;
    return luat_msgbus_put(&msg, 0);
}

int l_gpio_handler(lua_State *L, void* ptr) {
    (void)ptr; // unused
    // 给 sys.publish方法发送数据
    rtos_msg_t* msg = (rtos_msg_t*)lua_topointer(L, -1);
    int pin = msg->arg1;
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return 0;
    if (gpios[pin].lua_ref == 0)
        return 0;
    lua_geti(L, LUA_REGISTRYINDEX, gpios[pin].lua_ref);
    if (!lua_isnil(L, -1)) {
        lua_pushinteger(L, msg->arg2);
        lua_pushinteger(L, msg->arg1);
        lua_call(L, 2, 0);
    }
    return 0;
}

/*
设置管脚功能
@api gpio.setup(pin, mode, pull, irq, alt)
@int pin gpio编号,必须是数值
@any mode 输入输出模式：<br>数字0/1代表输出模式<br>nil代表输入模式<br>function代表中断模式，如果填gpio.count，则为中断计数功能，中断时不回调
@int pull 上拉下拉模式, 可以是上拉模式 gpio.PULLUP 或下拉模式 gpio.PULLDOWN, 或者开漏模式 0. 需要根据实际硬件选用
@int irq 中断触发模式,默认gpio.BOTH。中断触发模式<br>上升沿gpio.RISING<br>下降沿gpio.FALLING<br>上升和下降都触发gpio.BOTH 
@int alt 复用选项，目前只有Air780EXXX平台需要这个参数，有些GPIO可以复用到不同引脚上，可以选择复用选项（0或者4）从而复用到对应的引脚上
@return any 输出模式返回设置电平的闭包, 输入模式和中断模式返回获取电平的闭包
@usage

-- 设置gpio17为输入
gpio.setup(17, nil)

-- 设置gpio17为输出,且初始化电平为低,使用硬件默认上下拉配置
gpio.setup(17, 0)

-- 设置gpio17为输出,且初始化电平为高,且启用内部上拉
gpio.setup(17, 1, gpio.PULLUP)

-- 设置gpio27为中断, 默认双向触发
gpio.setup(27, function(val,io_num)
    print("io",io_num,val) -- 提醒, val并不代表触发方向, 仅代表中断后某个时间点的电平, io_num是IO序号
end, gpio.PULLUP)

-- 设置gpio27为中断, 仅上升沿触发
gpio.setup(27, function(val)
    print("IRQ_27",val) -- 提醒, val并不代表触发方向, 仅代表中断后某个时间点的电平
end, gpio.PULLUP, gpio.RISING)

-- 中断计数 于2024.5.8新增
-- 设置gpio7为中断计数，详细demo见gpio/gpio_irq_count
gpio.setup(7, gpio.count)

-- alt_func 于2023.7.2新增
-- 本功能仅对AIR780EXXX有效,仅用于调整GPIO复用,不能用于外设复用调整
-- 以下示例代码, 将I2S_DOUT复用成gpio18
-- AIR780E的PIN33(模块管脚序号), 对应paddr 38, 默认功能是I2S_DOUT, 复用成gpio18
-- 方向输出,且初始化电平为低,使用硬件默认上下拉配置
-- Air780E(GPIO复用请查阅 https://air780e.cn 首页硬件资料表格中的Air780E&Air780EG&Air780EX&Air700E_GPIO_table_20231227.pdf)
-- Air780EP(GPIO复用请查阅 https://air780ep.cn 首页硬件资料表格中的Air780E&Air780EG&Air780EX&Air700E_GPIO_table_20231227.pdf)
gpio.setup(18, 0, nil, nil, 4)

-- 提醒: 
-- 当管脚为输入模式或中断,才能通过gpio.get()获取到电平
-- 当管脚为输出模式,才能通过gpio.set()设置电平
-- 当管脚为输出模式,通过gpio.get()总会得到0
-- 中断回调的val参数不代表触发方向, 仅代表中断后某个时间点的电平
-- 对Cat.1模块,Air780E只有GPIO20~22才能双向触发，其他系列所有GPIO都能双向触发，具体看硬件手册
-- 默认设置下,中断是没有防抖时间的,可以通过gpio.set_debounce(pin, 50)来设置防抖时间

-- pull参数的额外说明, 上拉/下拉配置
-- 对于部分的BSP来说, 只支持 gpio.PULLUP 或 gpio.PULLDOWN, 但有部分BSP支持开漏模式
-- 对于支持开漏的bsp, pull参数要传 0 才能开启开漏模式, 不是传nil
-- 例如:
-- EC618系列(Air780E/Air780EG/Air780EX/Air700E等)
-- EC718系列(Air780EP/Air780EPV等)
-- XT804系列(Air101/Air103/Air601)
*/
static int l_gpio_setup(lua_State *L) {
    luat_gpio_t conf = {0};
    conf.pin = luaL_checkinteger(L, 1);
    if (conf.pin >= LUAT_GPIO_PIN_MAX) {
        LLOGW("id out of range 0 ~ %d, but %d", LUAT_GPIO_PIN_MAX, conf.pin);
        return 0;
    }
    //conf->mode = luaL_checkinteger(L, 2);
    conf.lua_ref = 0;
    conf.irq = 0;
    gpios[conf.pin].irq_type = 0xff;
    if (lua_isfunction(L, 2)) {
    	conf.irq_cb = 0;
        conf.mode = Luat_GPIO_IRQ;
        if (lua_tocfunction(L, 2) == l_gpio_get_count) {
        	if (gpios[conf.pin].lua_ref) {
                luaL_unref(L, LUA_REGISTRYINDEX, gpios[conf.pin].lua_ref);
                gpios[conf.pin].lua_ref = 0;
        	}
        	conf.irq_cb = luat_gpio_irq_count;
        	LLOGD("pin %d use irq count mode", conf.pin);
        } else {
            lua_pushvalue(L, 2);
            conf.lua_ref = luaL_ref(L, LUA_REGISTRYINDEX);
        }
        conf.irq = luaL_optinteger(L, 4, Luat_GPIO_BOTH);
        gpios[conf.pin].irq_type = conf.irq;

    }
    else if (lua_isinteger(L, 2)) {
        conf.mode = Luat_GPIO_OUTPUT;
        conf.irq = luaL_checkinteger(L, 2) == 0 ? 0 : 1; // 重用irq当初始值用
    }
    else {
        conf.mode = Luat_GPIO_INPUT;
    }
    conf.pull = luaL_optinteger(L, 3, default_gpio_pull);

    if (lua_isinteger(L, 5)) {
        conf.alt_func = luaL_checkinteger(L, 5);
    }
    else
    {
    	conf.alt_func = -1;
    }
    #ifdef LUAT_USE_DRV_GPIO
    int ret = luat_drv_gpio_setup(&conf);
    #else
    int ret = luat_gpio_setup(&conf);
    #endif
    if (ret != 0) {
        LLOGW("gpio setup fail pin=%d ret %d", conf.pin, ret);
        return 0;
    }
    if (conf.mode == Luat_GPIO_IRQ) {
        if (gpios[conf.pin].lua_ref && gpios[conf.pin].lua_ref != conf.lua_ref) {
            luaL_unref(L, LUA_REGISTRYINDEX, gpios[conf.pin].lua_ref);
            gpios[conf.pin].lua_ref = conf.lua_ref;
        }
        gpios[conf.pin].lua_ref = conf.lua_ref;
    }
    else if (conf.mode == Luat_GPIO_OUTPUT) {
        #ifdef LUAT_USE_DRV_GPIO
        luat_drv_gpio_set(conf.pin, conf.irq); // irq被重用为OUTPUT的初始值
        #else
        luat_gpio_set(conf.pin, conf.irq); // irq被重用为OUTPUT的初始值
        #endif
    }
    // 生成闭包
    lua_settop(L, 1);
    if (conf.mode == Luat_GPIO_OUTPUT) {
        lua_pushcclosure(L, l_gpio_set, 1);
    }
    else {
        lua_pushcclosure(L, l_gpio_get, 1);
    }
    return 1;
}
static int cap_target_level;//捕获目标电平
static uint64_t rising_tick,falling_tick;//捕获电平时记录到的系统tick64
int l_caplevel_handler(lua_State *L, void* ptr) {
    (void)ptr; // unused
    // 给 sys.publish方法发送数据
    rtos_msg_t* msg = (rtos_msg_t*)lua_topointer(L, -1);
    int pin = msg->arg1;
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return 0;
    if (gpios[pin].lua_ref == 0)
        return 0;
    lua_geti(L, LUA_REGISTRYINDEX, gpios[pin].lua_ref);
    uint64_t diff = 0;
    uint64_t us_int = 0;
    uint64_t us_float = 0;
    if (!lua_isnil(L, -1)) {
        if(cap_target_level == 1){
            diff = falling_tick - rising_tick;
        }else{
            diff = rising_tick - falling_tick;
        }
        us_int = diff / luat_mcu_us_period();
        us_float = diff % luat_mcu_us_period();
        lua_pushinteger(L, (uint32_t)us_int);
        lua_pushinteger(L, (uint32_t)us_float);
        lua_call(L, 2, 0);
    }
    return 0;
}
int luat_caplevel_irq_cb(int pin, void* args) {
    rtos_msg_t msg = {0};
    msg.handler = l_caplevel_handler;
    msg.ptr = NULL;
    msg.arg1 = pin;
#ifdef LUAT_GPIO_PIN_MAX
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX) {
#else
    if (pin < 0 || pin >= Luat_GPIO_MAX_ID) {
#endif
        return 0;
    }
    luat_gpio_t conf={0};
    conf.pin = pin;
    conf.mode = Luat_GPIO_IRQ;
    conf.irq_cb = luat_caplevel_irq_cb;
    conf.alt_func = -1;
    conf.pull=Luat_GPIO_DEFAULT;
    if(gpios[pin].irq_type == Luat_GPIO_RISING){
        rising_tick = luat_mcu_tick64();
        conf.irq =Luat_GPIO_FALLING;
        luat_gpio_setup(&conf);
        gpios[pin].irq_type = Luat_GPIO_FALLING;
        if(cap_target_level == 1){
            return 1;
        }else{
            return luat_msgbus_put(&msg, 0); 
        }
        
    }else{
        falling_tick = luat_mcu_tick64();
        conf.irq =Luat_GPIO_RISING;
        luat_gpio_setup(&conf);
        gpios[pin].irq_type = Luat_GPIO_RISING;
        if(cap_target_level == 1){
            return luat_msgbus_put(&msg, 0);
        }else{
            return 1;
        }
    }

}
/*
捕获管脚电平持续时长，单位us
@api gpio.caplevel(pin, level,func)
@int pin GPIO编号,必须是数值
@int level 需要捕获的电平, 可以是 高电平gpio.HIGH, 低电平gpio.LOW, 或者直接写数值1或0，即管脚上正常时间处于level的反，捕获设定的level持续时间
@function func 完成捕获后的回调函数，仅一个参数，参数为捕获到的时间长度number型数值，单位us
@return any 返回获取电平的闭包
@usage
-- 捕获GPIO7为高电平的持续时间
gpio.caplevel(7,1,function(us_int) print(us_float) end)
*/
static int l_gpio_caplevel(lua_State *L){
    luat_gpio_t conf = {0};
    conf.pin = luaL_checkinteger(L, 1);
    cap_target_level = luaL_checkinteger(L,2);
    //根据目标电平，配置管脚首先处理的沿
    if(cap_target_level == 1){//目标是捕获高电平
        conf.irq = Luat_GPIO_RISING;//管脚首先处理上升沿
    }else{
        conf.irq = Luat_GPIO_FALLING;
    }
    conf.mode=Luat_GPIO_IRQ;
    if (lua_isfunction(L, 3)) {
        lua_pushvalue(L, 3);
        conf.lua_ref = luaL_ref(L, LUA_REGISTRYINDEX);
        if (gpios[conf.pin].lua_ref && gpios[conf.pin].lua_ref != conf.lua_ref) {
            luaL_unref(L, LUA_REGISTRYINDEX, gpios[conf.pin].lua_ref);
        }
        gpios[conf.pin].irq_type = conf.irq;
        gpios[conf.pin].lua_ref = conf.lua_ref;
    }else{
        return 0;
    }
    conf.irq_cb = luat_caplevel_irq_cb;
    int re = luat_gpio_setup(&conf);
    if (re != 0) {
        LLOGW("gpio setup fail pin=%d", conf.pin);
        return 0;
    }
    // 生成闭包
    lua_settop(L, 1);
    lua_pushcclosure(L, l_gpio_get, 1);
    return 1;
}
/*
设置管脚电平
@api gpio.set(pin, value)
@int pin GPIO编号,必须是数值
@int value 电平, 可以是 高电平gpio.HIGH, 低电平gpio.LOW, 或者直接写数值1或0
@return nil 无返回值
@usage
-- 注意!!! 仅输出状态下,这个函数才有效
-- 一定要先gpio.setup, 起码执行过一次gpio.setup, 才能使用本函数. 但不需要每次都gpio.setup
-- 设置gpio17为低电平
gpio.set(17, 0)
*/
static int l_gpio_set(lua_State *L) {
    int pin = 0;
    int value = 0;
    if (lua_isinteger(L, lua_upvalueindex(1))) {
        pin = lua_tointeger(L, lua_upvalueindex(1));
        value = luaL_checkinteger(L, 1);
    }
    else {
        pin = luaL_checkinteger(L, 1);
        value = luaL_checkinteger(L, 2);
    }
    #ifdef LUAT_USE_DRV_GPIO
    luat_drv_gpio_set(pin, value);
    #else
    luat_gpio_set(pin, value);
    #endif
    gpio_bit_set(pin, (uint8_t)value);
    return 0;
}

/*
获取管脚电平
@api gpio.get(pin)
@int pin GPIO编号,必须是数值
@return value 电平, 高电平gpio.HIGH, 低电平gpio.LOW, 对应数值1和0
@usage
-- 注意!!! 仅输入模式或者中断模式状态下,这个函数才有效
-- 一定要先gpio.setup, 起码执行过一次gpio.setup, 才能使用本函数. 但不需要每次都gpio.setup
-- 获取gpio17的当前电平
local value = gpio.get(17)
log.info("gpio", "GPIO17:", value)
*/
static int l_gpio_get(lua_State *L) {
    int upindex = lua_upvalueindex(1);
    int value = 0;
    int pin = 0;
    if (lua_isinteger(L, upindex)) {
        pin = luaL_checkinteger(L, upindex);
    }
    else {
        pin = luaL_checkinteger(L, 1);
    }
    if (pin != 255) {
        #if defined(LUAT_USE_DRV_GPIO)
        int ret = luat_drv_gpio_get(pin, &value) & 0x01 ? 1 : 0;
        if (ret == 0) {
            value = (value & 0x01) ? 1 : 0;
        }
        #else
        value = luat_gpio_get(pin) & 0x01 ? 1 : 0;
        #endif
    }
    lua_pushinteger(L, value);
    return 1;
}

/*
关闭管脚功能(恢复高阻输入态),关掉中断
@api gpio.close(pin)
@int pin GPIO编号,必须是数值
@return nil 无返回值,总是执行成功
@usage
-- 关闭gpio17
gpio.close(17)
*/
static int l_gpio_close(lua_State *L) {
    int pin = luaL_checkinteger(L, 1);
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX)
        return 0;
    luat_gpio_close(pin);
    if (gpios[pin].lua_ref) {
        luaL_unref(L, LUA_REGISTRYINDEX, gpios[pin].lua_ref);
        gpios[pin].lua_ref = 0;
    }
#ifndef LUAT_RTOS_API_NOTOK
    if (gpios[pin].timer != NULL) {
        gpios[pin].conf_tick = 0;
        luat_rtos_timer_stop(gpios[pin].timer);
        luat_rtos_timer_delete(gpios[pin].timer);
        gpios[pin].timer = NULL;
    }
#endif
    return 0;
}

/*
设置GPIO脚的默认上拉/下拉设置, 默认是平台自定义(一般为开漏).
@api gpio.setDefaultPull(val)
@int val 0平台自定义,1上拉, 2下拉
@return boolean 传值正确返回true,否则返回false
@usage
-- 设置gpio.setup的pull默认值为上拉
gpio.setDefaultPull(1)
*/
static int l_gpio_set_default_pull(lua_State *L) {
    int value = luaL_checkinteger(L, 1);
    if (value >= 0 && value <= 2) {
        default_gpio_pull = value;
        lua_pushboolean(L, 1);
    }
    else {
        lua_pushboolean(L, 0);
    }
    return 1;
}

/*
变换GPIO脚输出电平,仅输出模式可用
@api gpio.toggle(pin)
@int 管脚的GPIO号
@return nil 无返回值
@usage
-- 本API于 2022.05.17 添加
-- 假设GPIO16上有LED, 每500ms切换一次开关
-- 注意!!! 仅输出状态下,这个函数才有效
gpio.setup(16, 0)
sys.timerLoopStart(function()
    gpio.toggle(16)
end, 500)
*/
static int l_gpio_toggle(lua_State *L) {
    int pin = 0;
    if (lua_isinteger(L, lua_upvalueindex(1)))
        pin = lua_tointeger(L, lua_upvalueindex(1));
    else
        pin = luaL_checkinteger(L, 1);
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX) {
        LLOGW("pin id out of range (0-127)");
        return 0;
    }
    uint8_t value = gpio_bit_get(pin);
    #ifdef LUAT_USE_DRV_GPIO
    luat_drv_gpio_set(pin, value == 0 ? Luat_GPIO_HIGH : Luat_GPIO_LOW);
    #else
    luat_gpio_set(pin, value == 0 ? Luat_GPIO_HIGH : Luat_GPIO_LOW);
    #endif
    gpio_bit_set(pin, value == 0 ? 1 : 0);
    return 0;
}

/*
在同一个GPIO输出一组脉冲
@api gpio.pulse(pin,level,len,delay)
@int gpio号
@int/string 数值或者字符串.
@int len 长度 单位是bit, 高位在前.
@int delay 高低电平延迟时间, 用的软件while来delay, 这里的delay值是while循环次数, 具体delay时间必须实际调试才知道
@return nil 无返回值
@usage
-- 注意, len的单位是bit, 高位在前，高低电平时间均是由delay决定。
-- 本API是阻塞操作，不可以一次性输出太多的脉冲！！！ 否则会死机!!!
-- 通过GPIO1脚输出输出8个电平变化，while循环次数是0
gpio.pulse(1,0xA9, 8, 0)
*/
static int l_gpio_pulse(lua_State *L) {
    int pin,delay = 0;
    char tmp = 0;
    size_t len = 0;
    char* level = NULL;
    if (lua_isinteger(L, lua_upvalueindex(1))){
        pin = lua_tointeger(L, lua_upvalueindex(1));
        if (lua_isinteger(L, 1)){
            tmp = (char)luaL_checkinteger(L, 1);
            level = &tmp;
        }else if (lua_isstring(L, 1)){
            level = (char*)luaL_checklstring(L, 1, &len);
        }
        len = luaL_checkinteger(L, 2);
        delay = luaL_checkinteger(L, 3);
    } else {
        pin = luaL_checkinteger(L, 1);
        if (lua_isinteger(L, 2)){
            tmp = (char)luaL_checkinteger(L, 2);
            level = &tmp;
        }else if (lua_isstring(L, 2)){
            level = (char*)luaL_checklstring(L, 2, &len);
        }
        len = luaL_checkinteger(L, 3);
        delay = luaL_checkinteger(L, 4);
    }
    if (pin < 0 || pin >= LUAT_GPIO_PIN_MAX) {
        LLOGD("pin id out of range (0-127)");
        return 0;
    }
    luat_gpio_pulse(pin,(uint8_t*)level,len,delay);
    return 0;
}

/*
防抖设置, 根据硬件ticks进行防抖
@api gpio.debounce(pin, ms, mode)
@int gpio号, 0~127, 与硬件相关
@int 防抖时长,单位毫秒, 最大 65555 ms, 设置为0则关闭
@int 模式, 0冷却模式, 1延时模式. 默认是0
@return nil 无返回值
@usage
-- 消抖模式, 当前支持2种, 2022.12.16开始支持mode=1
-- 0 触发中断后,马上上报一次, 然后冷却N个毫秒后,重新接受中断
-- 1 触发中断后,延迟N个毫秒,期间没有新中断且电平没有变化,上报一次

-- 开启防抖, 模式0-冷却, 中断后马上上报, 但100ms内只上报一次
gpio.debounce(7, 100) -- 对应GPIO7
-- 开启防抖, 模式1-延时, 中断后等待100ms,期间若保持该电平了,时间到之后上报一次
-- 对应的,如果输入的是一个 50hz的方波,那么不会触发任何上报
gpio.debounce(7, 100, 1)

-- 关闭防抖,时间设置为0就关闭
gpio.debounce(7, 0)
*/
static int l_gpio_debounce(lua_State *L) {
    uint8_t pin = luaL_checkinteger(L, 1);
    uint16_t timeout = luaL_checkinteger(L, 2);
    uint8_t mode = luaL_optinteger(L, 3, 0);
    if (pin >= LUAT_GPIO_PIN_MAX) {
        LLOGW("MUST pin < %d", LUAT_GPIO_PIN_MAX);
        return 0;
    }
    //LLOGD("debounce %d %d %d", pin, timeout, mode);
    gpios[pin].conf_tick = timeout;
    gpios[pin].latest_tick = 0;
    gpios[pin].debounce_mode = mode;
#ifndef LUAT_RTOS_API_NOTOK
    if ((mode == 0 && gpios[pin].timer != NULL) || timeout == 0) {
        luat_rtos_timer_stop(gpios[pin].timer);
        luat_rtos_timer_delete(gpios[pin].timer);
        gpios[pin].timer = NULL;
    }
    else if (mode == 1 && gpios[pin].timer == NULL && timeout > 0) {
        //LLOGD("GPIO debounce mode 1 %d %d", pin, timeout);
        if (gpios[pin].timer == NULL)
            luat_rtos_timer_create(&gpios[pin].timer);
        if (gpios[pin].timer == NULL) {
            LLOGE("out of memory when malloc debounce timer");
            return 0;
        }
    }
#endif
    return 0;
}

/*
获取gpio中断数量，并清空累计值
@api gpio.count(pin)
@int gpio号, 0~127, 与硬件相关
@return int 返回从上次获取中断数量后到当前的中断计数
@usage
log.info("irq cnt", gpio.count(10))
*/
static int l_gpio_get_count(lua_State *L) {
    uint8_t pin = luaL_checkinteger(L, 1);
    if (pin >= LUAT_GPIO_PIN_MAX) {
        LLOGW("id out of range 0 ~ %d, but %d", LUAT_GPIO_PIN_MAX, pin);
        lua_pushinteger(L, 0);
        return 1;
    }
    uint32_t v,cr;
    cr = luat_rtos_entry_critical();
    v = gpios[pin].irq_cnt;
    gpios[pin].irq_cnt = 0;
    luat_rtos_exit_critical(cr);
    lua_pushinteger(L, v);
    return 1;
}

#include "rotable2.h"

#if (defined CHIP_EC618) || (defined CHIP_EC718) || (defined CHIP_EC716)
#include "platform_define.h"
#endif

static const rotable_Reg_t reg_gpio[] =
{
    { "setup" ,         ROREG_FUNC(l_gpio_setup )},
    { "set" ,           ROREG_FUNC(l_gpio_set)},
    { "get" ,           ROREG_FUNC(l_gpio_get)},
    { "close" ,         ROREG_FUNC(l_gpio_close)},
    { "toggle",         ROREG_FUNC(l_gpio_toggle)},
    { "debounce",       ROREG_FUNC(l_gpio_debounce)},
    { "pulse",          ROREG_FUNC(l_gpio_pulse)},
    { "setDefaultPull", ROREG_FUNC(l_gpio_set_default_pull)},
	{ "count",			ROREG_FUNC(l_gpio_get_count)},
#ifdef LUAT_USE_MCU
    { "caplevel" ,      ROREG_FUNC(l_gpio_caplevel)},
#endif
    //@const NONE number 无效引脚,一般用于告诉底层某功能引脚不指定
    { "NONE",          ROREG_INT(LUAT_GPIO_NONE)},
    //@const LOW number 低电平
    { "LOW",            ROREG_INT(Luat_GPIO_LOW)},
    //@const HIGH number 高电平
    { "HIGH",           ROREG_INT(Luat_GPIO_HIGH)},

    { "OUTPUT",         ROREG_INT(Luat_GPIO_OUTPUT)}, // 留着做兼容

    //@const PULLUP number 上拉
    { "PULLUP",         ROREG_INT(Luat_GPIO_PULLUP)},
    //@const PULLDOWN number 下拉
    { "PULLDOWN",       ROREG_INT(Luat_GPIO_PULLDOWN)},

    //@const RISING number 上升沿触发
    { "RISING",         ROREG_INT(Luat_GPIO_RISING)},
    //@const FALLING number 下降沿触发
    { "FALLING",        ROREG_INT(Luat_GPIO_FALLING)},
    //@const BOTH number 双向触发,部分设备支持
    { "BOTH",           ROREG_INT(Luat_GPIO_BOTH)},
    //@const HIGH_IRQ number 高电平触发,部分设备支持
    { "HIGH_IRQ",       ROREG_INT(Luat_GPIO_HIGH_IRQ)},
    //@const LOW_IRQ number 低电平触发,部分设备支持
    { "LOW_IRQ",        ROREG_INT(Luat_GPIO_LOW_IRQ)},
#if (defined CHIP_EC618) || (defined CHIP_EC718) || (defined CHIP_EC716)

    //@const WAKEUP0 number 休眠唤醒脚0,不支持输出
    { "WAKEUP0",         ROREG_INT(HAL_WAKEUP_0)},
    //@const WAKEUP1 number VBUS,USB唤醒脚,不支持输出
    { "VBUS",            ROREG_INT(HAL_WAKEUP_1)},
    { "WAKEUP1",         ROREG_INT(HAL_WAKEUP_1)},
    //@const WAKEUP2 number USIM热插拔脚,不支持输出
    { "USIM_DET",        ROREG_INT(HAL_WAKEUP_2)},
    { "WAKEUP2",         ROREG_INT(HAL_WAKEUP_2)},
#if (defined CHIP_EC718) || (defined CHIP_EC716)
    //@const WAKEUP3 number 休眠唤醒脚3,与GPIO20是同一个引脚
    { "WAKEUP3",         ROREG_INT(HAL_WAKEUP_3)},
    //@const WAKEUP4 number 休眠唤醒脚4,与GPIO21是同一个引脚
    { "WAKEUP4",         ROREG_INT(HAL_WAKEUP_4)},
    //@const WAKEUP5 number 休眠唤醒脚5,与GPIO22是同一个引脚
    { "WAKEUP5",         ROREG_INT(HAL_WAKEUP_5)},
    //@const WAKEUP6 number 休眠唤醒脚6,,不支持输出
    { "WAKEUP6",         ROREG_INT(HAL_WAKEUP_CHARGE)},
    { "CHG_DET",         ROREG_INT(HAL_WAKEUP_CHARGE)},
#endif
    //@const AUDIOPA_EN number 音频PA使能脚, 仅Air780EHV特有的引脚
    { "AUDIOPA_EN",      ROREG_INT(HAL_GPIO_22)},
	//@const PWR_KEY number 开机键,支持双向触发中断,不支持输出
	{ "PWR_KEY",         ROREG_INT(HAL_WAKEUP_PWRKEY)},
#endif
	{ NULL,             ROREG_INT(0) }
};


LUAMOD_API int luaopen_gpio( lua_State *L ) {
    memset(gpios, 0, sizeof(gpio_ctx_t) * LUAT_GPIO_PIN_MAX);
    luat_newlib2(L, reg_gpio);
    return 1;
}

// -------------------- 一些辅助函数

void luat_gpio_mode(int pin, int mode, int pull, int initOutput) {
    if (pin == 255) return;
    luat_gpio_t conf = {0};
    conf.pin = pin;
    conf.mode = mode == Luat_GPIO_INPUT ? Luat_GPIO_INPUT : Luat_GPIO_OUTPUT; // 只能是输入/输出, 不能是中断.
    conf.pull = pull;
    conf.irq = initOutput;
    conf.lua_ref = 0;
    conf.irq_cb = 0;
    conf.alt_func = -1;
    #ifdef LUAT_USE_DRV_GPIO
    luat_drv_gpio_setup(&conf);
    if (conf.mode == Luat_GPIO_OUTPUT) {
        luat_drv_gpio_set(pin, initOutput);
    }
    #else
    luat_gpio_setup(&conf);
    if (conf.mode == Luat_GPIO_OUTPUT) {
        luat_gpio_set(pin, initOutput);
    }
    #endif
}

#ifndef LUAT_COMPILER_NOWEAK
void LUAT_WEAK luat_gpio_pulse(int pin, uint8_t *level, uint16_t len, uint16_t delay_ns) {

}
#endif