fix：修改pa管脚编号，复用方式改为pins

module/Air8000/demo/cc/main.lua

@@ -1,109 +1,111 @@
-
 -- LuaTools需要PROJECT和VERSION这两个信息
 PROJECT = "ccdemo"
 VERSION = "1.0.0"
 log.style(1)
 
-uart.setup(1, 115200)
 
-local up1 = zbuff.create(6400,0)
-local up2 = zbuff.create(6400,0)
-local down1 = zbuff.create(6400,0)
-local down2 = zbuff.create(6400,0)
+-- sys库是标配
+sys = require("sys")
+
+if wdt then
+    --添加硬狗防止程序卡死，在支持的设备上启用这个功能
+    --wdt.init(9000)--初始化watchdog设置为9s
+    --sys.timerLoopStart(wdt.feed, 3000)--3s喂一次狗
+end
+local up1 = zbuff.create(6400,0)        --上行数据保存区1
+local up2 = zbuff.create(6400,0)        --上行数据保存区2
+local down1 = zbuff.create(6400,0)      --下行数据保存区1
+local down2 = zbuff.create(6400,0)      --下行数据保存区2
 local cnt = 0
 
+gpio.setup(24, 1, gpio.PULLUP)          -- i2c工作的电压域
+gpio.setup(164, 1, gpio.PULLUP) -- es8311电源使能脚
+gpio.setup(162, 1, gpio.PULLUP) -- 喇叭pa功放脚
+pins.setup(80, "I2C0_SCL")      --复用pin80为i2c0_scl
+pins.setup(81, "I2C0_SDA")      --复用pin81为i2c0_sda
+
+local multimedia_id = 0         -- 音频通道 0
+local i2c_id = 0            -- i2c_id 0
+local i2s_id = 0            -- i2s_id 0
+local i2s_mode = 0          -- i2s模式 0 主机 1 从机
+local i2s_sample_rate = 16000   -- 采样率
+local i2s_bits_per_sample = 16      -- 数据位数
+local i2s_channel_format = i2s.MONO_R        -- 声道, 0 左声道, 1 右声道, 2 立体声
+local i2s_communication_format = i2s.MODE_LSB    -- 格式, 可选MODE_I2S, MODE_LSB, MODE_MSB
+local i2s_channel_bits = 16     -- 声道的BCLK数量
+
+local pa_pin = 162       -- 喇叭pa功放脚
+local pa_on_level = 1       -- PA打开电平 1 高电平 0 低电平
+local pa_delay = 100        -- 在DAC启动后，延迟多长时间打开PA，单位1ms
+local power_pin = 164         -- es8311电源使能脚
+local power_on_level = 1        -- 电源控制IO的电平，默认拉高
+local power_delay = 3       -- 在DAC启动前插入的冗余时间，单位100ms
+local power_time_delay = 100        -- 音频播放完毕时，PA与DAC关闭的时间间隔，单位1ms
+
+local voice_vol = 70        -- 喇叭音量
+local mic_vol = 65          -- 麦克风音量
+
 local function record(is_dl, point)
     if is_dl then
         log.info("下行数据，位于缓存", point+1, "缓存1数据量", down1:used(), "缓存2数据量", down2:used())
     else
         log.info("上行数据，位于缓存", point+1, "缓存1数据量", up1:used(), "缓存2数据量", up2:used())
     end
-	log.info("通话质量", cc.quality())
+    log.info("通话质量", cc.quality())
     -- 可以在初始化串口后，通过uart.tx来发送走对应的zbuff即可
 end
 
 sys.subscribe("CC_IND", function(state)
-    log.info("cc_status", state)
     if state == "READY" then
         sys.publish("CC_READY")
     elseif state == "INCOMINGCALL" then
-		cnt = cnt + 1
-		if cnt > 1 then
-			cc.accept(0)
-		end
+        cnt = cnt + 1
+        if cnt > 3 then
+            cc.accept(0)   --自动接听
+        end
     elseif state == "HANGUP_CALL_DONE" or state == "MAKE_CALL_FAILED" or state == "DISCONNECTED" then
-		audio.pm(0,audio.STANDBY)
-		-- audio.pm(0,audio.SHUTDOWN)	--低功耗可以选择SHUTDOWN或者POWEROFF，如果codec无法断电用SHUTDOWN
-	end
+        audio.pm(0,audio.STANDBY)
+        -- audio.pm(0,audio.SHUTDOWN)   --低功耗可以选择SHUTDOWN或者POWEROFF，如果codec无法断电用SHUTDOWN
+    end
 end)
 
-sys.taskInit(function()
-if cc then
-    log.info("支持cc库")
-    cc.on("record", record)
+function cc_setup()
+
     cc.record(true, up1, up2, down1, down2)
-end
-    local multimedia_id = 0
-    local i2c_id = 0
-    local i2s_id = 0
-    local i2s_mode = 0
-    local i2s_sample_rate = 16000
-    local i2s_bits_per_sample = 16
-    local i2s_channel_format = i2s.MONO_R
-    local i2s_communication_format = i2s.MODE_LSB
-    local i2s_channel_bits = 16
-
-    local pa_pin = 0      --  PA 使能开关
-    local pa_on_level = 1
-    local pa_delay = 100
-    local power_pin = 28      --  8311 使能开关
-    local power_on_level = 1
-    local power_delay = 3
-    local power_time_delay = 100
-
-    local voice_vol = 60
-    local mic_vol = 80
-
-    local find_es8311 = false
-    gpio.setup(24, 1, gpio.PULLUP)          -- 默认打开内部的I2C0 相关器件，不然I2C 初始化会失败
-    gpio.setup(power_pin, 1, gpio.PULLUP)            -- 打开es8311 的电源脚
-    gpio.setup(pa_pin, 1, gpio.PULLUP)               -- 打开pa 的电源脚
-    sys.wait(300)
-    i2c.setup(i2c_id, i2c.FAST)
-    if i2c.send(i2c_id, 0x18, 0xfd) == true then
-        log.info("音频小板或内置ES8311", "codec on i2c0")
-        find_es8311 = true
-    end
 
-    if not find_es8311 then
-        while true do
-            log.info("not find es8311")
-            sys.wait(1000)
-        end
-    end
+    pm.power(pm.LDO_CTL, false)  --开发板上ES8311由LDO_CTL控制上下电
+    sys.wait(100)
+    pm.power(pm.LDO_CTL, true)  --开发板上ES8311由LDO_CTL控制上下电
+
+    i2c.setup(i2c_id,i2c.FAST)      --设置i2c
 
     i2s.setup(i2s_id, i2s_mode, i2s_sample_rate, i2s_bits_per_sample, i2s_channel_format, i2s_communication_format,i2s_channel_bits)
 
     audio.config(multimedia_id, pa_pin, pa_on_level, power_delay, pa_delay, power_pin, power_on_level, power_time_delay)
-    audio.setBus(multimedia_id, audio.BUS_I2S,{chip = "es8311", i2cid = i2c_id, i2sid = i2s_id})	--通道0的硬件输出通道设置为I2S
+    audio.setBus(multimedia_id, audio.BUS_I2S,{chip = "es8311", i2cid = i2c_id, i2sid = i2s_id})    --通道0的硬件输出通道设置为I2S
 
     audio.vol(multimedia_id, voice_vol)
     audio.micVol(multimedia_id, mic_vol)
-    if cc then
-        sys.waitUntil("IP_READY")
-        
-        cc.init(multimedia_id)
 
-        audio.pm(0,audio.STANDBY)
-        sys.waitUntil("CC_READY")
-        -- sys.wait(3000)   
-        -- cc.dial(0,"10086") --拨打电话
-    end
-
-end)
+    cc.init(multimedia_id) --初始化电话功能
 
+    sys.waitUntil("CC_READY")
+    sys.wait(10000)
+    cc.dial(0,"15893470522") --拨打电话
+end
+cc.on("record", record)--注册cc事件回调
+sys.taskInit(cc_setup) --初始化cc
+
+-- sys.taskInit(function()
+--     while 1 do
+--         -- 打印内存状态, 调试用
+--         sys.wait(1000)
+--         log.info("lua", rtos.meminfo())
+--         log.info("sys", rtos.meminfo("sys"))
+--     end
+-- end)
 
 -- 用户代码已结束---------------------------------------------
 -- 结尾总是这一句
 sys.run()
--- sys.run()之后后面不要加任何语句!!!!!
+-- sys.run()之后后面不要加任何语句!!!!!